EPREVAEngineer Paper
Technical paperNot peer reviewedElectricalThermalEnergy

A first-order thermal model of a battery cell: derivation, parameters and a worked example

update · 5 Oct 2026
Version 2 adds a discrete-time form for battery management systems and a limitations section. Version 1 remains available.
Full paper ↓

A battery cell heats up when current flows. A simple model treats it like an electric RC circuit: a thermal resistance to the air and a heat capacity. Two numbers tell you how hot the cell gets (resistance × heat) and how fast (resistance × capacity).

⚑ AI-drafted summary · not yet checked by a human editor. The paper itself is always the primary source.

Abstract

We derive the lumped thermal model used in many battery management systems, show how its two parameters set the steady-state temperature rise and the response time, and work through an illustrative cylindrical-cell example with Ohmic heating of 2 W. Steady state is reached after about five time constants; with an illustrative thermal resistance of 8 K/W and heat capacity of 70 J/K the cell settles 16 K above ambient with a time constant of 560 s. The model ignores internal temperature gradients and entropic heat, which we discuss as limitations.

Keywords: battery · thermal model · BMS · lumped capacitance · heat generation

Introduction

Cell temperature drives battery ageing and safety, but few cells carry an internal sensor. Battery management systems (BMS) therefore estimate temperature with simple models. This note derives the most common one, the first-order lumped thermal model, and works through an example.

Model

Treat the cell as a single body at uniform temperature TT with heat capacity CTC_T, exchanging heat with ambient air at TaT_a through a thermal resistance RTR_T. An energy balance gives

CTdTdt=Ta−TRT+QC_T \frac{dT}{dt} = \frac{T_a - T}{R_T} + Q
(1)

where QQ is the heat generated inside the cell. Following the energy balance of Bernardi et al.[1] and neglecting the reversible (entropic) term, the heat generated is the irreversible loss

Q=I (VOCV−V)≈I2R0Q = I\,(V_{OCV} - V) \approx I^2 R_0
(2)

with R0R_0 the cell's internal resistance.

Steady state and time constant

Setting dT/dt=0dT/dt = 0 in (1):

ΔTss=RTQ\Delta T_{ss} = R_T Q
(3)
Playground · Temperature rise from thermal resistance
solve for
Temperature rise
10 K
Plot temperature rise against
1,00000.01200 K/W (log)

For a step in QQ at t=0t = 0, the solution of (1) is

T(t)=Ta+RTQ(1−e−t/τ),τ=RTCTT(t) = T_a + R_T Q \left(1 - e^{-t/\tau}\right), \quad \tau = R_T C_T
(4)

Worked example

ParameterValue
Current I10 A
Internal resistance R_020 mΩ
Heat Q = I²R_02.0 W
Thermal resistance R_T8 K/W
Heat capacity C_T70 J/K
Time constant τ560 s
Steady-state rise ΔT16 K

Assumptions

  • Uniform cell temperature (lumped capacitance), valid when the Biot number is small.
  • Constant RTR_T, CTC_T and R0R_0.
  • Entropic heat neglected.

Discrete form for a BMS

A BMS samples at a fixed step Δt\Delta t. Holding QQ constant over each step, (4) gives the exact recursion

T[k]=ϵ T[k−1]+(1−ϵ)(Ta+RTQ[k−1]),ϵ=e−Δt/τT[k] = \epsilon\, T[k-1] + (1-\epsilon)\left(T_a + R_T Q[k-1]\right), \quad \epsilon = e^{-\Delta t/\tau}
(5)

which costs one multiply-add per sample. The same structure appears in Chowdhury and Lu's one-shot identification method[3], where (5) is rearranged to be linear in its parameters so that they can be fitted by least squares.

Limitations

  • Large cells and fast pulses. Internal gradients make the surface cooler than the core; a two-node (core/surface) model is needed.[2]
  • Entropic heat. Near-zero currents and some chemistries make the reversible term in Bernardi's balance significant.
  • Changing cooling. RTR_T depends on airflow; a fan or a neighbouring hot cell changes it.

References

  1. D. Bernardi, E. Pawlikowski and J. Newman, "A General Energy Balance for Battery Systems," Journal of the Electrochemical Society, vol. 132, no. 1, pp. 5–12, 1985.
  2. C. Forgez, D. V. Do, G. Friedrich, M. Morcrette and C. Delacourt, "Thermal modeling of a cylindrical LiFePO4/graphite lithium-ion battery," Journal of Power Sources, vol. 195, no. 9, pp. 2961–2968, 2010.
  3. M. A. Chowdhury and Q. Lu, "Equivalent-Circuit Thermal Model for Batteries with One-Shot Parameter Identification," arXiv:2503.12616, 2025. arxiv.org/abs/2503.12616

Use it

Reproduce this work

Data available— not provided
Code available— not provided
BOM available— not provided
Test procedure✓ yes
Environment described— not provided
Software versions— not provided
Hardware described— not provided
Parameters listed✓ yes

Sign in to register a replication attempt.

Open Engineering Review

Typed, signed comments on method, data and calculations. This is open discussion — it is not formal peer review.

No comments yet.

Sign in to add a typed review comment. Reviews are signed with your name.