EPREVAEngineer Paper
SOLARAnalysisMaterialsEnergyManufacturing

MicroQuanta and Zhejiang University report 23.9% certified efficiency for 19.48 cm² perovskite mini-module

The National PV Industry Measurement and Testing Center certified the steady-state result. The team says cooling the wet precursor film before vacuum treatment reduced fill factor losses.

small rectangular perovskite mini-module on glass with visible laser-scribed subcell lines, gloved hand or tweezers holding the thin glass module, cleanroom lab setting with slot-die coater or vacuum chamber equipment
AI-generated image

What was certified

The National PV Industry Measurement and Testing Center (NPVM) of China's Fujian Metrology Institute certified the result, and the team describes it as a new world record.

Corresponding author Dongchen Lan said the record was achieved at module level rather than in a small laboratory cell. "Solar cells often lose efficiency when scaled up into modules," he said.

The authors are from MicroQuanta Semiconductor, Zhejiang University, China Three Gorges Renewable, the Zhejiang Provincial Key Laboratory of Optoelectronic Functional Materials and Devices, and the Australian Centre for Advanced Photovoltaics.

Fill factor identified as the main loss

The researchers first compared laboratory-scale perovskite solar cells with mini-modules fabricated under matched processing conditions in previous studies. They used Shapley value analysis, which averages the contribution of each parameter across all possible orders of substitution, to quantify how open-circuit voltage, short-circuit current density and fill factor contributed to the measured efficiency loss.

After accounting for current losses in inactive areas created by laser scribing, the team found that fill factor was the largest contributor to the efficiency drop from cells to modules. The mini-module had a fill factor of 83.3%, which the authors say is the highest for a perovskite module, and a geometric fill factor of 97%, meaning 97% of its aperture area was photoactive.

How the cooling step works

To reduce the fill factor loss, the team spin-coated a perovskite precursor onto indium tin oxide (ITO)-coated glass carrying two hole-transport layers. Immediately after coating, they cooled the wet film for 15 seconds to 0–10 °C, transferred it to a vacuum chamber within about five seconds, and vacuum-flashed it for two minutes before annealing it at 110 °C for 30 minutes. They then applied a surface passivation layer and deposited the electron-transport layers and a silver electrode.

Measurements during film formation showed that cooling slowed the conversion of an intermediate phase into perovskite, yielding films with larger, more uniform grains.

The 19.48 cm² mini-module was made by slot-die coating and consisted of eight subcells connected in series through laser scribing. It was built on a glass substrate coated with ITO, nickel oxide (NiOₓ) and a self-assembled monolayer known as 3PATAT-C3. The device featured a formamidinium-cesium lead iodide (FA₀.₉₅Cs₀.₀₅PbI₃) absorber with an ethylenediammonium diiodide surface passivation layer, a fullerene (C₆₀) electron transport layer, a bathocuproine buffer layer and a silver electrode.

Aging tests and the authors' conclusion

In separate aging tests under continuous one-sun illumination at open-circuit, the efficiency loss attributable to declining fill factor was less than one-third as large in modules made with the cooling step as in control modules, according to the team's measurements.

The group concluded that the fill factor advantage is retained across device scales and during operation, revealing what it described as a shared parameter-level pattern between scale-up loss and operational decay. "Hence, preserving fill factor offers a unifying optimization target for developing efficient, stable and scalable perovskite photovoltaics," the authors wrote.

Lan said the team identified a major cause of the losses and demonstrated a way to mitigate them while helping modules maintain their performance over time. "This addresses a key challenge in bringing next-generation solar technologies closer to practical use," he told pv magazine.

Earlier results and production plans

In January 2025, MicroQuanta achieved a certified efficiency of 21.86% for an 810 cm² perovskite solar module. The company has also been developing a gigawatt-scale perovskite production line in Quzhou, Zhejiang province, with plans to manufacture large-area modules measuring 2.88 m² and targeting 20% efficiency and a 25-year lifespan.

More recently, MicroQuanta introduced a perovskite-silicon tandem module for building-integrated photovoltaics at The smarter E Europe 2026 in Munich, Germany. The four-terminal MQ-α² series features a reported efficiency of 26% and power outputs ranging from 65 W to 165 W, with customizable colors and finishes.

Technical fact box

  • 23.9 % — certified steady-state efficiency of the 19.48 cm² perovskite mini-module
  • 83.3 % — fill factor of the mini-module, reported as highest for a perovskite module
  • 97 % — geometric fill factor, share of aperture area that was photoactive
  • 8 — number of subcells connected in series through laser scribing
  • 15 s — cooling time of the wet precursor film to 0–10 °C
  • 2 min — vacuum-flash time before annealing at 110 C for 30 min
  • Less than one-third — efficiency loss from declining fill factor in cooled modules relative to control modules in aging tests

Sources

  1. MicroQuanta, Zhejiang University achieve world-record efficiency of 23.9% for 19.48 cm² perovskite solar module — pv magazine

Other news outlets are named as sources but not linked.

Discussion

Technical questions and corrections are welcome. Comments are signed and checked before they appear.

No comments yet.

Sign in to add a typed review comment. Reviews are signed with your name.

More analysis